Ionizer Support Unit
Products
500 LPH ALKALINE IONIZER SUPPORT UNIT
Size : 40” x 40”
Drive motor : Single Phase
Working pressure: 1.5 – 3.5 kg/cm2
Price : 2,00,000.00/- + GST
Shipping Charges : Free
Quantity :
Plant Design Basis and Conditions
We have designed this system to produce permeate flow 500 Liters per hour.
Maximum TDS Level of Raw Water (input) upto 2500 ppm.
The treated water quality as required i.e pH 7-8 after correction ,TDS <100 PPM & Hardness < 50 PPM can be achieve , subject to the feed water quality is the same as specified above .In case of any change in the quality of raw water it may have implication on operating parameters or on end results of the system.
The system of recovery is properly maintained corresponding to the raw water TDS. Plant feed water limiting conditions as mentioned below are strictly maintained,
| Parameter | Results | |
| Turbidity | < 1 NTU | |
| Free Chloride | Nil | |
| Oil & Grease | Nil | |
| Iron | <0.1 PPM | |
| SDI | <4.0 | |
| Temperature | < 45 degree C | |
| 500 LPH SYSTEM | ||
| SCOPE OF SUPPLY |
TECHNICAL DETAILS
| Description | Quantity | |
| Raw Water Feed Pump with motor | 1 no. | |
| Sand Media filter | 1 no. | |
| Activate Carbon filter | 1 no | |
| Anti scalent Dosing pump | 1 no | |
| Housing with filter 5 micron | 2 nos | |
| SS Multistage high pressures pump | 1 nos | |
| Membrane Housing 4080 E2 FRP | 1 nos | |
| Imported Special Designed Membrane High rejection ( 60%)Brackish | 2 nos. | |
| Water | 4040 | |
| Multi Port Valves 3/4” in & out Imp | 2nos | |
| Fine filtered water-blending line with micron Filter, PVC pipe line and fittings | 1 lot. | |
| MS electrical panel with controls | 1 no | |
| Pressures Gauges | 3 nos | |
| Rota meter reject & permeate | 2 nos | |
| SS Skid | 1 no | |
| Row water feed pump Type | Monoblock Centrifugal | |
| Material of Construction | C.I | |
| Make | CRI , Kirloskar | |
| Drive motor | SinglePhase | |
| Sand Media Filter | ||
| Working | Down flow | |
| Max flow rate | 3m3/hr | |
| Min. flow rate | 0.5 m3/hr | |
| Working pressure | 1.5 – 3.5 kg/cm2 | |
| Size | 10”X54” | |
| Make | Pentair | |
| Valves | Multiport valve 25mm | |
| Carbon Filter | ||
| Working | Down flow | |
| Max flow rate | 3m3/hr | |
| Min.flow rate | 0.5m3/hr | |
| Working pressure | 1.5 – 3.5 kg/cm2 | |
| Size | 10”X54” | |
| Make | Pentair | |
| Valves | Multiport valves 25mm | |
| Anti Scalant Dosing Unit | ||
| Make | IMP | |
| Capacity | 6 LPH @ 3.5 bar | |
| MICRON CARTRIDGE FILTER | ||
| Quantity | 1 sat | |
| Flow rate | 3m3/hr | |
| Rating | 10 micron | |
| Make | Filtech / USF | |
| CARTRIDGE HOUSING | ||
| Quantity | 2 nos. | |
| Make | Polycarbonate | |
| High Pressure Pump | ||
| Type | Multistage Centrifugal | |
| Make | CRI/shakti | |
| Drive motor | Single Phase | |
| Model | CDL- 2-18 | |
| Membrane Housing Type | FPR | |
| PSI | 250 | |
| Make | ALFA, Imp | |
| Size | 4080 E2 | |
| MEMBRANE | ||
| Type | High Rejection Brackish water | |
| Membrane | CSM /hi-tech/Vontron | |
| Modal | 4040 | |
| Size | 40” x 40” | |
| Rejection | 60% Max. | |
| FLOW METER | ||
| Quantity | 2 nos | |
| Type | Glass Tube Rota mater | |
| Make | Flow max, IMP |
